Extron P/2 DA4xi Four Output VGA Distribution Amplifier

 29,95 incl. 23% BTW

The Extron P/2 DA4xi is a one input VGA distribution amplifier that splits a signal and distributes it to four separate outputs. With 350 MHz (-3dB) RGB video bandwidth, fully loaded, the P/2 DA4xi is compatible with VGA-QXGA graphic cards, projectors and flat panel displays. Each output is individually buffered and amplified to help maintain the original signal integrity and eliminate noise interference. The P/2 DA4xi also includes a video gain switch which boosts the signal for long cable runs.

Features

  • Input: One female 15-pin HD connector
  • Output: Four female 15-pin HD connectors
  • 350 MHz (-3 dB) RGB video bandwidth, fully loaded
  • Compatible with VGA-QXGA resolutions
  • Drives outputs up to 250 feet (75 meters)
  • Video gain switch
  • Rack and under-desk mountable
  • ID Bits routed to local monitor output
  • 1U, half rack width 6″ deep metal enclosure
  • Internal Extron Everlast™ power supply — Provides worldwide power compatibility, with high‑demonstrated reliability and low power consumption for reduced operating cost
ideo
   Gain 0 dB or +3 dB (when input is 0.7 Vp-p, output is 0.7 V or 1.0 V), switchable
   Bandwidth 350 MHz (-3 dB), fully loaded
Video input
   Number/signal type 1 VGA-QXGA RGBHV, RGBS, RGsB, RsGsBs, HDTV component video, S-video, composite video
    NOTE These DAs are compatible with all the signal formats listed above when the gain DIP switch is set to 0.7 V. They are compatible with only RGBHV and RGBS when the gain DIP switch is set to 1.0 V.
   Connectors 1 female 15-pin HD (optional Mac/VGA adapters are available)
   Pin connections ID bits on pins 4, 11, 12, and 15 are passed through to local monitor output (loop-through).
The pin 9 connection is passed through to output 1.
   Nominal level 1.0 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video
   Minimum/maximum levels Analog: 0.3 V to 1.5 Vp-p with no offset at unity gain
   Impedance 75 ohms
   Horizontal frequency 15 kHz to 135 kHz
   Vertical frequency 30 Hz to 150 Hz
   Return loss <-40 dB @ 5 MHz
   Input coupling DC
Video output
   Number/signal type
      P/2 DA4xi 4 VGA-QXGA RGBHV, RGBS, RGsB, RsGsBs, HDTV component video, S-video, composite video (follows input type)
      P/2 DA6xi 6 VGA-QXGA RGBHV, RGBS, RGsB, RsGsBs, HDTV component video, S-video, composite video (follows input type)
    NOTE These DAs are compatible with all the signal formats listed above when the gain DIP switch is set to 0.7 V. They are compatible with only RGBHV and RGBS when the gain DIP switch is set to 1.0 V.
   Connectors
      P/2 DA4xi 4 female 15-pin HD
      P/2 DA6xi 6 female 15-pin HD
   Nominal level 1.0 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video
   Minimum/maximum levels 0.3 V to 1.5 Vp-p (follows input)
   Impedance 75 ohms
   Return loss <-40 dB @ 5 MHz
   DC offset ±5 mV with input at 0 offset
Sync
   Input type RGBHV, RGBS, RGsB, RsGsBs; bi-level and tri-level sync
   Output type RGBHV, RGBS, RGsB, RsGsBs; bi-level and tri-level sync (follows input)
    NOTE These DAs are compatible with all the signal formats listed above when the gain DIP switch is set to 0.7 V.
   Input level 1.8 V to 5.0 Vp-p
   Output level TTL: 5.0 Vp-p, unterminated
   Input impedance 510 ohms
   Output impedance 50 ohms
   Max. propagation delay 60 ns
   Max. rise/fall time 2 ns
   Polarity Positive or negative (follows input)
General
   Power Internal
100-240 VAC, 50-60 Hz, 12 watts
   Ambient temperature/humidity Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
   Cooling Convection, no vents
   Mounting
      Rack mount Yes, with optional 1U rack shelf
      Furniture mount Yes, with optional under-desk mounting kit or through-desk mounting kit
   Enclosure type Metal
   Enclosure dimensions 1.6″ H x 8.7″ W x 6.0″ D (1U high, half rack wide)
(4.1 cm H x 22.1 cm W x 15.2 cm D)
(Depth excludes connectors.)
   Product weight 2.0 lbs (0.9 kg)
   Shipping weight 3 lb (2 kg)
   DIM weight
      USA/Canada 3.7 lbs (1.7 kg)
      International 4.3 lbs (2.0 kg)
   Vibration ISTA 1A in carton (International Safe Transit Association)
   Regulatory compliance
      Safety CE, c-UL, UL
      EMI/EMC CE, C-tick, FCC Class A, ICES, KCC, VCCI
      Environmental Complies with the appropriate requirements of RoHS, WEEE

Refurbished

Artikelnummer: 25158 Categorie:

Extra informatie

Gewicht 2 kg
Translate »